Interferential low-frequency device Sedante Crea

Clea incorporates new technology while preserving the origins of the interferential current low-frequency therapy device. The 4-pole interference adopted in Clea achieves delicate and gentle stimulation. The ST mode allows for a variety of stimulations through the use of eight cups. Furthermore, the range of treatments has expanded with the addition of new stimulation methods, such as stimulation of motor points using probe electrodes.

Features

10,000 Hz carrier frequency

It is effective for cases involving subjective discomfort, unusual sensations, and tenderness, such as myofascial pain syndrome of the erector spinae muscles. The stimulation using a 10,000 Hz carrier frequency feels very gentle, and it relieves pain by delivering a large amount of current to the living body.
Versatile ST stimulation modes

If you are experiencing muscle tension or pain in the shoulders, stimulating the upper trapezius and the area around the scapula can increase scapular mobility and further enhance shoulder joint mobility. The ST mode, with its diverse stimulation, not only relieves pain but also improves mobility.
Local stimulation by probe

There are various factors that limit joint range of motion, such as joint capsule contracture and muscle atrophy. Probe-based electrical stimulation is effective when changing stimulation points on the fly during treatment, or when used in combination with manual therapy. *The probe is an optional accessory.
Neuromuscular stimulation with belt electrodes

Muscle atrophy caused by prolonged bed rest or joint immobilization takes time to improve muscle function, including muscle strength. Neuromuscular stimulation via belt electrodes can induce strong muscle contractions even in patients who cannot perform voluntary contractions, thus facilitating early mobilization. *Belt electrodes are optional accessories.
Versatile therapy modes
CI (combined IFC) mode

By alternating between IFC and IFCW treatments, the interference current works deep into the area, creating the sensation of kneading while moving. A pleasant stimulation envelops the affected area. This mode incorporates the essence of an interferential current low-frequency therapy device.
CM (combined modulation) mode

It alternately stimulates between the poles using two different modulation waveforms. It provides the sensation of kneading while tapping the muscle. This is effective for patients who are relatively accustomed to stimulation.
ST mode

By varying the carrier frequency and independently changing the modulation waveform for each pole, it outputs highly random and diverse stimuli. The rhythmic action linked between each pole activates the muscle pump function.
NM (normal) mode

It is a traditional interference mode by Dr. Nemec. You can treat patients with IFCW, which provides a sense of movement, and NMES, which allows for increasing and decreasing output aimed at muscle strengthening.
NMES mode

In C레a, synchronization between CH1 and CH2, as well as alternating operation between the red and white leads of each channel, is now possible. The ability to alternately stimulate agonist and antagonist muscles has expanded the range of treatments for muscle re-education.
Operability
5-year manufacturer warranty

To ensure you can use it with peace of mind for years to come, it comes with a 5-year manufacturer's warranty.

Note: Repairs in the following cases are subject to a charge even during the warranty period.
• In the event of failure or damage resulting from failure to observe the intended use, contraindications, precautions, operating procedures, maintenance and inspection methods, and other matters described in the instruction manual and attached documents.
• In the case of failure or damage caused by fire, earthquake, wind and flood damage, lightning strike, other natural disasters, pollution, salt damage, gas damage, abnormal voltage or use of an unspecified power source, theft, etc.
• In the case of malfunction or damage caused by transportation, movement, dropping, or impact after purchase
• In the event of maintenance or repair performed by anyone other than our company or a contractor designated by us
• Maintenance or repair using replacement parts other than those specified by our company, or if the product has been modified
Replenishment of consumables and naturally worn parts
Repair to restore scratches or wear from use
If the warranty is lost or cannot be shown
Other faults or damage not deemed our responsibility

Main Specifications

Item	content
Product code	SD-5602
Brand name	Sedante Crea
Generic name	Low-frequency and interference current low-frequency therapy combination physical therapy device
Medical device certification no.	229AIBZX00003000
Power	AC100 / 240V 50/60Hz
Dimensions	W420 x D397 x H1,297 (mm)
Weight	40 kg
JMDN code	70620000
Classification	Controlled device specially designated (repair class 6)
Power consumption	230VA
Output voltage	100Vp-p (at 500Ω load and 5000Hz carrier frequency)
Output current	70 mArms or below
Output waveform	sine wave
Included DC component	None
Effective load impedance range	500-4000 ohm
Carrier frequency	2500Hz, 5000Hz, 10000Hz
Treatment waveform	Sine modulated wave
Interference frequency	1 ~ 200pps (1 PPS step)
Vector time	1-9 sec (1-sec steps)
modulation factor	OFF, 50%, 100%, burst
Interval time	On 0-99 sec, rest: 0-99 sec (1 sec steps)
Mode setting	Cl, CM, ST, NM, P1, P2, P3
Interference setting	IFC, IFCW, NMES
Frequency band setting	Low, medium, and high frequency
Suction setting	Continuous, 1, 2, 3
Suction pressure adjustment	OFF, -5 to -23 kPa
SHS temperature control	OFF, 1-5, preheat
Treatment time	1 to 99 minutes (1-minute steps), continuous *Default setting: 1 to 30 minutes
Monitor	Current level meter (70 mArms)
Number of outputs	4-pole output 2CH x2
Other	Auto suction
Safety device	overcurrent stop, imbalance stop, lead disconnect stop, auto-zero start, auto-lock, key lock, SHS lead temperature sensor control
Electric shock protection	Class I device with Type BF applied part
Service life	8 years (by our standard)
Operating environment	Ambient temperature 10 to 40°C, relative humidity 30 to 75%, atmospheric pressure 700 to 1,060 hPa, applied part maximum temperature 43°C (however, when the ambient temperature is 40°C)